扫描二维码关注官方公众号
返回列表 发布新帖

[巴法络] 完蛋,WVL买了2天改机就改城砖了

5140 7
发表于 2012-5-30 20:40:26 | 显示全部楼层 阅读模式

来吧兄弟,一起玩一起讨论!

您需要 登录 才可以下载或查看,没有账号?注册

×
开机开不了,电源灯一直闪,闪完就是错误灯一直闪,每次6下
什么方法都试过了,硬盘也拿下来重新格了,也换过硬盘,都没用,电脑就是发现不了NAS
看了很多改机得教程,也搜了很多次,没见谁改机改成砖的啊
有没有朋友遇到过这种情况?

评论7

c1235Lv.4 发表于 2012-5-30 21:05:17 | 显示全部楼层
试试能不能进EM模式重刷固件
回复 点赞

使用道具 举报

eblis楼主Lv.3 发表于 2012-5-30 23:17:53 | 显示全部楼层
c1235 发表于 2012-5-30 21:05
试试能不能进EM模式重刷固件

请问要怎么进EM模式?进去然后怎么做?我找了一下好像没有类似得方法
回复 点赞

使用道具 举报

pt880Lv.10 发表于 2012-5-31 10:14:16 | 显示全部楼层
eblis 发表于 2012-5-30 23:17
请问要怎么进EM模式?进去然后怎么做?我找了一下好像没有类似得方法

LinkStation (LS-CHL, LS-XHL LS-VL , LS-WTGL and LS-WXL, LS WVL)
NOTE: The FUNCTION button for the LS-CHL and LS-XHL series is located on the front of the NAS whereas the LS-WTGL has the FUNC button on the back.
         1. Make sure that your NAS is powered off
         2. Hold down the FUNC/FUNCTION button for at least 6 seconds before powering the NAS on (LS-CHL and LS-XHL have their function button on the front whereas the LS-WTGL and LS-WXL have theirs on the back)
         3. While continuing to hold down the FUNC/FUNCTION button power the NAS on
            At this point it varies for these units so please read carefully:
                * LS-CHL and : The FUNCTION button will start blinking at which point you release the button and hold it down for an additional 10 seconds or until the FUNCTION button goes solid. At this point you may release the FUNCTION button
                * LS-WTGL and : The POWER light on the front of the unit will begin blinking blue rapidly at which point you may release the FUNC button. The POWER light should turn green in approximately 60 seconds
                * LS-XHL, LS-WXL, LS-VL and LS- WVL : These units do not have any procedure to boot into EM mode. The unit will automatically boot into EM mode if it needs to. If the unit is not booting at all you need to follow the TFTP boot procedure for the LS-XHL and LS-WXL. At the moment the LS-VL and LS-WVL units do not have a TFTP boot program and a fix is being worked on.
NOTE: If you still don't see the device on the NAS Navigator after 120 seconds, then I would suggest performing a TFTP boot.
   1. Once the NAS shows up on the NAS Navigator you may attempt to access your data or re-flash the firmware
回复 点赞

使用道具 举报

momoVIP互助团队 发表于 2012-5-31 13:18:37 | 显示全部楼层
打buffalo的售后热线吧,可以直接换新机。你就直接说机器开不到机了。
隔壁网希捷酷狼8T硬盘,正品国行,3年换新,只需要1320元,赠送论坛邀请码和VIP!
回复 点赞

使用道具 举报

bgtzhangLv.5 发表于 2012-6-7 15:53:00 | 显示全部楼层
其实你可以在官网下载最新固件试试,只要能找到NAS,就还有希望。换是没有问题的,但是麻烦点
回复 点赞

使用道具 举报

哇哈哈Lv.4 发表于 2012-6-7 16:16:10 | 显示全部楼层
直接换新机,又可以重新折腾,多爽
回复 点赞

使用道具 举报

TaoEricLv.2 发表于 2012-8-27 17:21:49 | 显示全部楼层
楼主说说看后来怎么解决的?
回复 点赞

使用道具 举报

回复

懒得打字嘛,点击右侧快捷回复 【本站酷狼4T,750元】
您需要登录后才可以回帖 登录 | 注册

本版积分规则

投诉/建议联系

support@gebi1.cn

未经授权禁止转载,复制和建立镜像,
如有违反,追究法律责任
  • 关注公众号
  • 添加微信客服
Copyright © 2001-2024 隔壁网 版权所有 All Rights Reserved. 粤ICP备14056481号-1
关灯 在本版发帖
扫一扫添加微信客服
返回顶部
快速回复 返回顶部 返回列表